Tight Enclosures HYDRA are applicable, among others, in the energy sector, automation, telecom-munication industry, and especially in places with a large extent of contamination and also places exposed to flooding (production plants, waste water treatment plants, coastal area). Specially designed construction of the enclosure provides effective protection of internal devices against the negative influence of external factors (dust, corrosive fumes, water).

Basic parameters:

HYDRA enclosures are made of glass fiber rein-forced polyester, they are corrosion resistant aga-inst the impact of chemicals and solvents.Enclosures HYDRA are available in two versions, depending on the degree of protection IP:

• IP65 with 2-point locking system with 2 locks;

• IP66 – equipped with 4-point locking system, which includes: tight lock ZIP66, rod and lo-cking elements, arranged on the perimeter.

The doors of enclosure are equipped with polyu-rethane gasket. It is possible to reverse the door (left/right).

The casing type KH 00 is made of glass fiber reinforced polyester and consists of two elements: a casing and a door with an opening angle of 180 °.
Can be sealed. There is a cable entry at the bottom of the housing. Fuse bases and clamps of various types can be installed in the housing.
KH 00 enclosures with fuses up to 100A are used as connecting devices between the external electrical network and the consumer’s network, they can also be installed in cabinets as the main protection.

Main settings:

Tight control cabinets, depending on mounted equipment, can be used for low voltage switchgears building, control cabinets for supervision of production processes.
Construction:

• Materiał: AZ150 Aluzinc steel sheet,
• Elements connected by means of riveting, screwing and welding,
• Single door for a cabinet width less than or equal to 1000 mm,
• Double door for a cabinet width greater than 1000mm,
• EPDM gasket applied to the edge of the cabinet,
• Flat roof,
• Slope roof (optional equipment),
• Roof and base with a notch enabling cable glands mounting,
• 3-point lever lock for patented locking cylinder,
• Cabinets, socles and roofs powder coated.

Features:

• Corrosion resistance,
• Back wall and sides perforations for mounting equipment on any height and depth,
• Dierent types of socles enables placing on dierent surfaces.

Basic parameters:

Installation method:

• C10 – on socles h=100mm,
• CW – non free-standing socles with a inspection panel, h=400mm,
• CZ – on socles designed to put in the ground, h=900mm,
• CW+CZ – on socles designed to put in the ground with inspection panel, h=1300mm,

Operating conditions:

• W – indoors,
• Z – outside.

Optional equipment:

• Mounting plates,
• Socles,
• Cable gland plates,
• Slope roof.

Frame cabinets, depending on the equipment installed in them, can be used for constructing LV switchgears, monitoring of electrical devices, supervision of production processes or as network cabinets in telecommunications. The cabinets can be combined with each other in sets. One of them can serve as a supply field, other as outlet, next as measuring. Frame cabinets are made of AZ150 aluzinc steel sheet.
Construction:

• cabinet framework: it is made in the form of a frame consisting of vertical and horizontal profiles
• connected by a plastic corner,
• single door for a width less than or equal to 1000 mm,
• double door for a width greater than 1000mm,
• in the basic configuration, the doors are equipped with a 4-point closure,
• lever lock for patented locking cylinder,
• unpainted frame skeleton,
• powder coated covers, doors and pedestals.

Features:

• the ability to connect cabinets in sets,
• thanks to the use of aluzinc perforated frame profiles and one type of self-forming screws (M6), the mechanical structure is stable and enables any configuration of equipment assembly,
• removable covers ensure easy access to the interior of the cabinet.

Installation method:

• C10 – on socless h = 100mm (possibility of stacking).

Basic parameters:

Operating conditions:

• W – inside.

Basic equipment:

• frame,
• door.

Optional equipment:

• Side panels,
• Rear panels,
• Socles,
• Mounting plates,
• Brackets,
• Cable gland plates.

Frame cabinets, depending on the equipment installed in them, can be used for constructing LV switchgears, monitoring of electrical devices, supervision of production processes. The cabinets can be combined with each other in sets. The material of the cabinet and pedestal is made of carbon steel DC01.
Construction:

• components connected with each other by welding,
• single door for a width less than or equal to 1000mm,
• double doors for a width greater than 1000mm,
• 4-point lever lock for patented locking cylinder,
• powder coated cabinets and pedestals.

Operating conditions:

• W – inside in dry condition.

Features:

• possibility to connect cabinets in sets,
• perforated frame allows for easy assembly of equipment,
• selection of the degree of IP tightness depending on the cabinet operating conditions,
• removable side and rear panels provide free access to the interior of the cabinet.

Installation method:

• CR1 on socles with a height equal to 100mm.

Basic parameters:

• frame + door.

Optional equipment:

• BRW- internal side walls (IP41),
• BRZ- external side walls (IP55),
• PRW- internal back (IP 41),
• PRZ- external back (IP55),
• CR1- a socle with a height equal 100mm,
• CR2- a socle with a height of 200mm,
• K.KD,KG,KN- cable glands plates,
• P1- mounting plates,
• ZM- modular construction,
• DW- internal doors,
• NSR- corner cabinets.

SK cabinets allow the assembly of control, distribution and measurement equipment. Cabinet and socle is made of aluminum alloy sheet ENAW 5754 with a thickness of 2,0mm . Elements are joined by riveting, screwing and welding.
Construction:

• single door for a cabinet width less than equal 850mm, double door for a cabinet width greater than 850mm,
• slope roof,
• 3-point lever lock for patented locking cylinder,
• CW free-standing socles equipped with control door,
• powder coated cabinets and socles.

Installation method:

• C10 on socles with a height equal to 100mm,
• CW on free-standing socles height equal to 400mm with a inspection panel,
• CZ on socles designed to put in the ground with inspection panel h=900mm,
• CW + CZ on socles designed to put in the ground with inspection panel,
• FZ on concrete pedestals

Basic parameters:

Operating conditions:

• outside in an industrial amd seaside environment

Features:

• corrosion resistance,
• back wall and side perforations for mounting equipment on any hegiht and depth,
• dierent types of socles enables placing on dierent terrain.

Free-standing switchgear enclosures are designed for switchgears construction that are used for distribution and measurement of electricity in multi-family buildings. They are equipped with a set of power counter and modular fuses. They can be join in sets both free-standing and wall mounted.
Construction:

• 1.2mm thick carbon steelshaped by punching and bending joined by riveting and welding,
• powder coating,
• hinged doors with 3 point lock, LE40Ucz.

Installation method:

• C10- on socles height 100mm.

Features:

• corrosion resistance,
• Back wall and sides perforations for mounting equipment on any height and depth, Dierent types of socles enables placing on dierent surfaces.

Basic parameters:

Operating conditions:

• W- indoors.

Basic equipment:

• cabinet with full doors without back,
• C – profiles, brackets, counter plates,
• masking panels,
• socle 100mm.

Optional equipment:

• back wall,
• cable glands MC.

Enclosures for electrical switchboards, control devices for production processes and machines.
Construction:

• carbon steel sheet DC01 for indoor enclosures,
• AZ150 Aluzinc steel sheet for outdoor enclosures,
• corpus welded (W) or riveted (Z),
• single door with a machine molded polyurethane (PUR) gasket. Hinged doors can be installed on the left and right side,
• one-point lock for key D5,
• mounting holes on the back wall,
• threaded bolts for the assembly of metal equipment,
• powder coating.

Installation method:

• N-wall mounted;
• CW- 400mm height freestanding socle with a inspection panel,
• CZ- 900mm socle designed to be put in the ground with a inspection panel.

Operating conditions:

• indoor in a dry environment,
• outdoor – wet and more agressive environment.

Basic parameters:

Basic equipment:

• key lock 1333.

Optional equipment:

• P – mounting plate,
• ZM – modular construction,
• PPK – cable gland plates,
• CW – freestanding socle,
• CZ – socle designed to be burried in the ground,
• DJ – slope roof.

The hygienic enclosure OHS is intended for the installation of electrical equipment in food, pharmaceutical and cosmetics industry.
Construction:

• material: V2A stainless steel sheet (1.4301) or V4A acid-proof steel polished (1.4404),
• doors mounted on internal hinges, equipped with a silicone gasket,
• the ability to put the hinges on the left side,
• 2-point locking system,
• IP69K stainless steel locks – FDA compliant sealing,
• 2-element construction (body + door).

Operating indoorsi:

• indoors in humid and agressive environments

Features:

• Corrosion resistant cabinet (caused by water, steam, air moisture, food acids, organic and non organic acids, cleaning and disinfecting agents) as well as the eects of temperatures,
• the cabinet has no gaps in which dirt and bacteria may cumulate,
• slope roof prevents accumulation of dust and dirt on the top,
• surface of the cabinet and make cleaning much easier
• front edge of the roof protects the upper part of the gasket against dirt,
• tightness,
• hygienic,
• non – toxic,
• no maintenance required,
• permanent,
• smooth surfaces of the cabinet for easier cleaning.

A line of innovative composite and aluminum poles perfectly suited to elegant, stylisedspaces. Thanks to the decorative base poles have a decorative function, emphasising the character and increasing the attractiveness of the surrounding.

Advantages

• elegant design
• no scrap value
• lightconstruction

What is more

• resistant to pollution
• it blends in perfectly with stylish, small architecture
• safe and economical maintenance

Application

• HoReCa
• developers
• parks, squares, streets
• mansion objects

Check additional solutions

• Possibility to choose a column made of composite or aluminum with a composite base
• LED strips illuminating the base, improve the visibility and fulfil the decorative function
• bases of columns can also play the role of road posts
• possibility to produce pole in any colour according to the RAL palette

Choose a variant for yourself

DECORPOLE stylised composite lighting column mounted in the ground SKPW-ST and mounted on foundation SKPF-ST

At the customer’s request, it is possible to produce columns with non-standard parameters. Possibility to strengthen the pole for difficult operating conditions.

The composite rod, apart from the unprecedented lightness combined with durability, are a full insulator, which will eliminate the use of a hoop.
Due to the fact that the composite poles are made of polyester-glass composite, they are characterized by:

• durability – the pole is resistant to road salt and other means used to clear snow from roads, traffic pollution, animal urine, bark beetles and woodpeckers; there is no problem with dew point, icing, flooding of wires inside the pole. It does not soak, does not break or break. The composite rod is elastic and resilient – the yield point disappears, at which permanent deformation occurs, and the exceeded tip force does not cause deformation of the column.
• safety – the production of the pole is ecological and the pole is 100% recyclable. The resistance of the rod to UV rays and low and high temperatures is the result of the use of appropriate materials for its production. Flammability tests have shown that the composite is a flame-retardant and vandal-resistant material. The Eko composite rod meets the requirements of PN-EN 1317 regarding passive safety, which is so important in recent times. In a collision, the pole absorbs energy only to a small extent – the vehicle continues to travel after the collision, but at a reduced speed. Research has shown that the ASI index – acceleration intensity, in accordance with PN-EN 1317, is five times lower than in the case when the effects of a collision are dangerous or fatal for the people in the vehicle. The rod is made of polyester-glass composite, which is why it is an insulator.
• low maintenance cost – The Eko composite rod is an ultra-light product (for a height of 9 m and a tip force of 2.5 kN, the weight is only about 60 kg), easy to transport and assemble. Installation does not require the use of a crane. Two fitters can set up a pole in a short time. The advantage is the fact that the pole can be installed not only in forest, mountainous areas with difficult access, but also in built-up areas. In addition, the composite is not a scrap value, so there are no additional costs related to the theft of the rod elements. The fact that the composite is an insulator means that periodic insulation tests are unnecessary.

More advantages of the composite wire can be found in the COMPOSITE tab
The EKO composite rod is manufactured in the same technology as the composite lighting pole, which obtained the Certificate of Conformity (CE) with the European standard PN-EN 40-7. Their design and production are carried out in accordance with the standards of the ISO 9001: 2008 quality management system.

ECO RODS TABLES

POLE ARMOR

• ROD DIGGED INTO THE GROUND – foundation without additional supporting elements; a column inserted into a drilled hole and filled with native soil
• FOUNDATION UI (with the U-85K plate) – the U-85K floor plate is a replacement for the U-85 type standing plate, made of a light and very durable composite, combining the simplicity of the U-85 standing plate, lightness and several times greater strength than a traditional concrete slab

The service power pole is used during the modernization of the line. It is used „pole for pole”. The great advantage of these poles is that they can be stored in any energy area. Power can be restored temporarily when no special equipment is involved. This can be done by the crew of the energy emergency.

OPTION – 2-SEGMENT ENERGY SERVICE POST

Diagram of the bypass as an ad hoc method during modernization, bringing measurable benefits for the LV line operator

SERVICE ENERGY POLE WITH AN EXHAUST – FUNCTIONAL ON THE BASIS

SERVICE ENERGY POST
The order of placing the service pole:

• Place the support on the ground and level it, selecting the ground under it until the maximum contact with the ground is obtained (do not sprinkle it);
• Put one layer of the standing boards on the base;
• Screw the carrying bolts and the plate to the base as shown in the drawing No. 1;
• Assemble the service pole as a whole by pressing the pin fi 8 in the hole to block both segments in the middle and connect the pole with the bottom plate of the bracket using the hinge pin;
• Place the service pole in a vertical position, setting it in a vertical position using the nuts on the carrying bolts;
• Lock the bolt connection by tightening the nuts with the torque shown in the figure;
• Place the remaining 5 layers of the standing boards on the load-bearing base.

ATTENTION! The service power pole will be able to transfer the load with the assumed bending moment under the following conditions:

• The strength of the soil under the stall will be equal to or greater than 31.8 kN / m2
• The stall will be loaded with six layers of siding plates, each 600x850x60mm
• The outer dimensions of the base of the parking lot will be 1530x1530mm

POST BASE PLAN
Correction consisting in removing or adding plates is unacceptable.

Eko-Sz reinforced composite poles complete the offer of supporting structures for the construction of overhead lines. These are poles reinforced with polyurethane foam, suitable for mounting in stilts.

TABLE OF POLES Eko-Sz

OPTIONAL ARMAMENT OF THE POLE:

• construction for insulator;
• construction clamps;
• stilts.

The mobile service line is a complete solution to supply consumers during modernization works on the existing line or in the event of a breakdown. One of its main tasks is to minimize the need for interruptions in electricity supply. When there is a need to build a service line (so-called bypass), we have a ready set for its creation.

Advantages:

• a quick way to eliminate failure – easy installation,
• reduction of SAIDI and SAIFI indicators,
• lower power failure fees,
• poles that do not interfere with the ground – no formal and legal problems,
• cheaper in operation compared to the use of a power generator

Basic equipment:

• 10 holes for transporting 10 pcs. service poles and service bases;
• haul-off box;
• lighting retractable mast;
• service cable winch with a cleaning system extending the service life of the cable;
• electrical socket boxes for MV connectors

Additional elements of equipment (possibility of individual selection of elements for the basic version):

• composite service poles;
• service pole lattice base;
• reusable ENSTO cable in accordance with PN-HD 620 S2: 2010E;
• generator;
• accessories for service poles.

Take advantage of the possibility of external financing through subsidies from European funds or national programs up to 70% of the value and enjoy the benefits of the MOBILE SERVICE LINE! Additionally, you can take advantage of the leasing offer for a MOBILE SERVICE LINE.
See the movie how the MOBILE SERVICE LINE works